Well I realise that I am pretty indecisive on some things.  I have booked the welding professional to come and do the welding.  He is coming in 8 days time and I am somewhat relieved.  I am also going to take the wings to be dipped that week as well.

In preparation for these events I got down to checking the shrouds for cracks and holes so that I could  mark them and ensure that I don't miss any on the day.  Whilst doing that I saw the boot lid hanging from the rafters and got it down to see if it needed any work.  The frame was located in the boot lid but not welded in so it just fell out when provoked.  So, yes it also needs welding.  I then looked at the front bonnet and realised that it is really awful so I took a trip to the store cupboard that is my In-Laws and brought my spare steel one back.  Fortunately it is in much better condition although it does have some holes in the main skin near the front corners which may have been used for straps, anyway, they are going.  I also need to do some work on the brackets that bolt to the hinges, one side is completely missing.  I have a vague memory of buying some of those from John so I will have to have a look.

I spent a few hours working on the boot lid and made some progress but still need a little more.

Had a lovely day in the garage today which considering it is a miserable January day makes it all the better.

I started but bolting on the rear off side wing which went pretty easily.  I had to modify the position of the bottom of the wing to the rear of the wheel arch as it was too high.  I then proceeded to look at the front wing.  Miraculously I found the 4 pieces of steel that form the captive nuts for the bolts that hold the wing support trim which I cleaned up and painted before slotting them back into the wing.  What was a pain was finding a set of bolts to fit into them.  I have no idea what thread they are and it took about 20 minutes routing around all the bolts I have before I had found a suitable pair.

Before putting the wing on I had a detailed look at the welding on the rear edge of the wing that I had done recently having previously ground the wing back to make the door gap work.  I think this will come back to haunt me at some point.  Anyway I decided that it wasn't good enough so had another go at it with the MIG welder.  Lost of welding and grinding later I bolted the wing on.

I also noticed that there is  a bit of research needed for the A post.

I had never looked at the return checking device.  When I did it was obvious something was wrong (apart from the fact that I am holding it the wrong way round that is).  Having looked up the brochures on the Ahead 4 Healey's web site I realise I have the wrong one.  Damn.  Especially as it will be another £90 to get it rectified.  I'm tempted to have a go at making a plate myself. Something to ponder over.

I am thinking of the next steps now.  I have decided to buy the gas welding equipment from Tinmantech rather than go for a cheap TIG or pay a professional to do it.  I am essentially troubled by the prospect of a professional charging me a lot of money and then finding another fault that requires welding.  Also, I think I must be able to learn how to do it myself, it might be fun even.  My wife is going to Miami in 5 weeks which means she can collect it and bring it back to avoid me paying the import duties.  Working out what I need to order at the moment.

I am also thinking of getting the wings dipped, I realise I have been here before but it seems the safest option.  I think I could take them to be dipped in my next holiday in 5 weeks.  They are basically ready but I need to get them fully bolted on first.  I mean that I have been using just a few of the bolts to put them in place rather than every single bolt hole.  I am a bit troubled that when I bolt them up properly that some of the holes won't line up.  I think this would be good thing to get done before I take the wings to be treated.

Once done I can then weld up the chassis.  This will be fun.  Then I will have a choice, do I start to fit up the drive train or do I do all the filler work on the wings?  I know the filler work will make a lot of mess so I am thinking that this should be done first.  Against that though is the problem of what I would do with the wings whilst I do the mechanics.  After all, I wouldn't want them getting scratched or knocked if they are ready for paint.  Decisions, decisions.

Christmas is a good time for garage time and I got a few days in the garage this week.  I put the wing back on and got a sensible door gap, all good.   I did need to reshape the lower front edge of the wing and was happy with how it turned out.

Feeling quite happy with that I took the car out of the garage to get some photos:

Wow, it has been over a month.  I did go to the classic car show in the Birmingham NEC and had a lovely, though very damp time.  I had intended to drive the regular run around but when I went to leave I noticed that the front tyre was flat.  So flat in fact that it would not trigger the pump in the garage so I brought it back home.  I could have pumped it up at home but decided that if it gets that flat I probably should get in replaced rather than contemplate a 250 mile round trip.  So even though it was absolutely lashing it down with rain I took the Triumph.  I discovered within 10 miles that my waterproof clothing wasn't actually waterproof.  It was awful.  Anyway, once there I had  lovely time.

I have found a mobile welder that will do the shrouds for £300 plus a bonus for working at a weekend.  This is troubling me a little as I can buy an AC TIG machine from China for £400 and then get the gas for another £100.  I realise that this is more but I would then have the equipment for life.  I have posted the question on a UK welding forum and the responses leave me feeling very demotivated. The people that say I should get the professional to do it outnumber the 'have a go yourself' brigade by some margin.

Talking of demotivated I looked at the car again this morning and knew that I needed to finish the door gaps, again.  So I removed the rear wing and B post before cleaning it up:

I then took to the rear edge off the front wing with a grinder and literally ground the wing back to provide a better level of gap.  I spent a few happy hours welding and grinding before repeating it again, and again.

I have manage a few days with the Healey this week which has been very enjoyable.  I cleaned up and finished off some of the welding that is required in the areas covered by the inner wings.

I then decided to look at the driver side wing as it was looking a little out in the length with the new shroud position.  This means that the process I went through a long time ago to remove a piece of metal was in need of reversal, frustratingly.  I could see the required length by looking at the front and by measuring the gaps between the wheels and the wheel arches of both front wings.  The replacement went quiet smoothly and now the car bodywork is looking very much closer to being ready for the next stage.  One of the other developments created by the movement of the shroud is that whilst the driver side needed extending the passenger side needs the reverse; the dreaded door gaps are not ideal.  This will require visiting before I move much further on and I need a little strength for it so I will leave it a few days.

I have decided to get the shrouds welded professionally rather than buying the equipment and doing it myself.  In an ideal world I would like a mobile welder to visit me and do the shrouds in situ.  I have contacted several suitable looking companies and await there views on the project.  I am off to the classic car show in Birmingham in a few weeks and this is one of the topics I will investigate whilst there.

Now that the half term holiday is coming to an end it is back to work for me.

These are the pictures that should have been with the last post but for some reason my phone didn't import them for a few days?

Anyway, the wing looking tired:

This is the inner wing on the near side:

And on the off side, except I forgot about the mole grips whilst taking them so one can't see what I was hoping to show, sausage features springs to mind.

The inner wings on both sides trial fitted and looking ok from the inside:

The next two photos are cool, they show a similar position with regards to the inner wing joint for both sides.  Phew.

The next two show one side with a tab for connecting to the top of the shroud / wing on one wing with it missing on the other.  I know it was there and I don't remember removing it,......